Site Logo

popsoft.com.hk

有關DacEasy & POP 系統
 
現在的時間是 23 7月 2018 03:29

所有顯示的時間為 UTC + 8 小時




發表新文章 回覆主題  [ 1 篇文章 ] 
發表人 內容
 文章主題 : Raid0 to Raid6
文章發表於 : 19 9月 2015 10:27 
離線

註冊時間: 24 9月 2008 10:58
文章: 71
Overview Raid:
Many RAID levels employ an error protection scheme called "parity", a widely used
method in information technology to provide fault tolerance in a given set of data.
Most use simple XOR, but RAID 6 uses two separate parities based respectively on
addition and multiplication in a particular Galois field or Reed–Solomon error correction.[14]

Standard RAID levels:
RAID can also provide data security with solid-state drives (SSDs) without the expense of an all-SSD system.
For example, a fast SSD can be mirrored with a mechanical drive. For this configuration to provide a significant
speed advantage an appropriate controller is needed that uses the fast SSD for all read operations.
Adaptec calls this "hybrid RAID".

A number of standard schemes have evolved. These are called levels. Originally, there were five RAID levels,
but many variations have evolved, notably several nested levels and many non-standard levels
(mostly proprietary). RAID levels and their associated data formats are standardized by the Storage
Networking Industry Association (SNIA) in the Common RAID Disk Drive Format (DDF) standard:

RAID 0
RAID 0 consists of striping, without mirroring or parity. The capacity of a RAID 0 volume is the sum of the
capacities of the disks in the set, the same as with a spanned volume. There is no added redundancy for
handling disk failures, just as with a spanned volume. Thus, failure of one disk causes the loss of the entire
RAID 0 volume, with reduced possibilities of data recovery when compared to a broken spanned volume.
Striping distributes the contents of files roughly equally among all disks in the set, which makes concurrent
read or write operations on the multiple disks almost inevitable and results in performance improvements.
The concurrent operations make the throughput of most read and write operations equal to the throughput
of one disk multiplied by the number of disks. Increased throughput is the big benefit of RAID 0 versus
spanned volume.

RAID 1
RAID 1 consists of data mirroring, without parity or striping. Data is written identically to two (or more)
drives, thereby producing a "mirrored set" of drives. Thus, any read request can be serviced by any drive
in the set. If a request is broadcast to every drive in the set, it can be serviced by the drive that accesses
the data first (depending on its seek time and rotational latency), improving performance. Sustained read
throughput, if the "controller" or "software" is optimized for it, approaches the sum of throughputs of every
drive in the set, just as for RAID 0. Actual read throughput of most RAID 1 implementations is slower than
the fastest drive. Write throughput is always slower because every drive must be updated, and the slowest
drive limits the write performance. The array continues to operate as long as at least one drive is functioning.

RAID 2
RAID 2 consists of bit-level striping with dedicated Hamming-code parity. All disk spindle rotation is synchronized
and data is striped such that each sequential bit is on a different drive. Hamming-code parity is calculated
across corresponding bits and stored on at least one parity drive. This level is of historical significance only;
although it was used on some early machines (for example, the Thinking Machines CM-2), as of 2014 it is not
used by any of the commercially available systems.

RAID 3
RAID 3 consists of "byte-level striping" with dedicated parity. All disk spindle rotation is synchronized and data
is striped such that each sequential byte is on a different drive. Parity is calculated across corresponding bytes
and stored on a dedicated parity drive. Although implementations exist, RAID 3 is not commonly used in practice.

RAID 4
RAID 4 consists of "block-level striping" with dedicated parity. This level was previously used by NetApp, but has
now been largely replaced by a proprietary implementation of RAID 4 with two parity disks, called RAID-DP.

RAID 5
RAID 5 consists of "block-level striping" with distributed parity. Unlike in RAID 4, parity information is distributed
among the drives. It requires that all drives but one be present to operate. Upon failure of a single drive,
subsequent reads can be calculated from the distributed parity such that no data is lost. RAID 5 requires at least
three disks. RAID 5 is seriously affected by the general trends regarding array rebuild time and the chance of drive
failure during rebuild. Rebuilding an array requires reading all data from all disks, opening a chance for a second
drive failure and the loss of entire array.
In August 2012, Dell posted an advisory against the use of RAID 5 in any configuration on Dell EqualLogic arrays
and RAID 50 with "Class 2 7200 RPM drives of 1 TB and higher capacity" for business-critical data.

RAID 6
RAID 6 consists of "block-level striping" with double distributed parity. Double parity provides fault tolerance
up to two failed drives. This makes larger RAID groups more practical, especially for high-availability systems,
as large-capacity drives take longer to restore. RAID 6 requires a minimum of four disks. As with RAID 5,
a single drive failure results in reduced performance of the entire array until the failed drive has been replaced.
With a RAID 6 array, using drives from multiple sources and manufacturers, it is possible to mitigate most of
the problems associated with RAID 5. The larger the drive capacities and the larger the array size, the more
important it becomes to choose RAID 6 instead of RAID 5. RAID 10 also minimizes these problems.


回頂端
 個人資料  
 
顯示文章 :  排序  
發表新文章 回覆主題  [ 1 篇文章 ] 

所有顯示的時間為 UTC + 8 小時


誰在線上

正在瀏覽這個版面的使用者:沒有註冊會員 和 1 位訪客


不能 在這個版面發表主題
不能 在這個版面回覆主題
不能 在這個版面編輯您的文章
不能 在這個版面刪除您的文章
不能 在這個版面上傳附加檔案

搜尋:
前往 :  
cron
Powered by phpBB, Almsamim WYSIWYG © 2000, 2002, 2005, 2007 phpBB Group
正體中文語系由 竹貓星球 維護製作